Posts

Showing posts with the label riveting

A note on multi-grip rivets and grip size.

Image
TAF supplies Gesipa multi-grip rivets. This means these rivets can be used on varying thicknesses of material, and therefore "grip" various total thicknesses, hence the name. The rivets have two lines where the material folds over, a lower and and a top one. When the thickness line sup with these lines, rivets look one way, whereas if the material thickness is somewhere in between, they look another. This image illustrates this well: Note how the right and left most rivets look, with the widest part of the bulge flush with the material, versus the two middle ones, where the bulge is a little removed from the material, looking more like a mushroom. I came across a situation where I had two rivets of the same diameter, but different lengths, and used what I later realized was probably not the length the factory had intended (the plans were silent on this). I ended up with rivets looking like this: Now  had never seen this before, because normally you use rivets...

Misaligned holes, or rookie mistake?

Image
I have been riveting my HS, and have run into a bit of a snag: Note the bent metal. This is where the two front spar channels meet. I had some hole alignment issues on my first try, so I unclecoed and reclecoed everything, and things went better at first, and a number of rivets are indeed set: But then I noticed the above, possibly a little later than I should have. The remainder of the rivets to set on that side of the HS will not go in (See the two matching rows of clecoes below, on the flanges of the spar). Note how the "top" ones are set. There is some misalignment left, however small, and I can't proceed further without having to do some things I'm not sure about at this point. ​Thoughts so far: One solution i could contemplate: match-drill/ream the problematic holes, and just keep going. Once the two holes where the bend is situated are "used" (to attach to the airframe I presume), it might all end up solid enough. The holes ...

Riveting decision

I'll spare you the suspense: I'm not going to do it. Here's why: From a strict engineering perspective, I shouldn't: The holes are over-sized, even for an over-size rivet. Rivet manufacturer says I should not do this. Even the clamping force doesn't seem to do enough to provide proper full grip. The hole does not "close in around the rivet" as I had hoped. As it turns out, the best-bet rivet for this application does NOT have an expanding shank. It really wants a tight fit from the get-go. My tests were done without reaming, which would enlarge the holes even more, and make the problems previously identified even worse. Being in a slightly too large hole, the rivet can set off-center, which is highly undesirable. I can't find any other combination of rivets/tooling that comes close to the over-sized CherryMAX approach. These rivets are quite expensive, would likely add 1000$+ to the project. I probably wouldn't be ahead financially in...

Flush riveting experiments

Image
Before getting to building my empennage, I still need to determine whether I will be able/willing to attempt a flush riveted Sling 4. I tried a number of things, and took lots of pictures, but I'll try to summarize the process and keep it short. Don't hesitate to contact me if you want details. General process: Take some spare sheet metal 6061-T6, 0.016 thickness (That's the skin material). Make two parts that I will rivet together. Drill 1/8th holes (3.3mm), one in each part. Dimple each part with a standard 1/8th dimple die. Rivet the two parts together with a CherryMAX oversize flush head pulll rivet CR3242-4-2. Observe closely. Cut down the middle, and observe closely again. See if I think such a joint will hold up. Here is what one will see when analyzing the hole and dimpling process: Pretty! Right? Note that there are 2 edges. As later testing revealed, this is chamfer from the deburring tool. This is magnified 200x. The diameter of th...

To flush or not to flush?

Image
I would really like to use flush rivets on my airframe ... they look better, you get a bit more performance/fuel economy from less drag, and they supposedly yield a stronger joint. Also, I'm already tool'ed up for it. But, the Sling 4 is designed around standard, dome-headed, blind rivets! What to do? Well first of all let's read up on blind rivets: Some of the things that differentiate them are: Materials used which in turn affect shear and tensile strength, as well as corrosion resistance. Their initial diameter, and the size of the hole they can fill. Their grip range. Their type, such as closed or open-ended, multi-grip, etc. etc. there are MANY MANY types of rivets from many vendors, making things far less straightforward than with a solid rivet. Unlike solid rivets, they don't fill their hole as easily and flexibly, this means that for flush rivets, the final hole, post-dimpling, has to be reamed to the proper size, which in turn means that the initia...