Posts

Showing posts with the label fuselage

Front floor and insulation progress

Image
I have finally moved forward and begun putting the front floor together, testing with both layers: And then added the foam insulation through the floor of the center fuselage: I was debating whether to bother with the foam, since it is listed as "sound insulation" on the parts list, and modern headsets do a pretty good job of that already. It turns out however that this product is primarily a fireproof barrier, so good safety-wise, and also acts as a decent thermal insulator. So, in it goes!

Finally some progress with the main spar carry-through

Image
After an inevitable slow down during the gorgeous summer months, I had to deal some health issues, which means that progress ground to a near stop for several months. In the past couple of weeks I have finally managed to get back into it. I had some troubles with the main spar which caused some frustrations. Although the holes I think were all in the right place, the main spar has a spring to it, which means that even when fully clecoed in, things weren't aligned quite right. So when I checked the gap where the main spars will fit, nothing was right! AND the holes had been matched drilled and enlarged incorrectly, uh oh. It turns out the best practice is to put a precise and correct spacer where the main spar would go, and to then secure the main spar accordingly. Of course, the manual does NOT mention any of this. Then I needed to fix those holes. That wasn't too bad. After checking with the factory, I could oversize to 1/4 inch, which is the size of the hole wher...

Center fuselage progress

Image
After long boring work prepping the metal, I finally started assembling everything yesterday! All went quite smoothly!

Main spar and center fuselage progress

Image
Test fitted some of the parts to be attached to the main spar: As it turns out however, the tube guides should not be assembled yet. You will find that the vesconite bushing mentioned in the plans is already mounted to the control tube, and therefore cannot be installed at this stage. I will instead mount the tube guides around the bushing on the control tube, and the whole thing will get attached to the main spar later ... this is how others did it as well it appears. Look for a future blog entry where i will likely show this later! I've also been prepping the numerous other parts for that section of the fuselage. I decided for the first time to remove a strip of protective film, instead of the hole thing all at once. You do this by using a soldering iron to melt a line in the film, allowing to cut it without damaging the underlying skin: Very easy to do and works nicely! Here is the gear mounting box with some connecting parts I am testing for fit and makin...

Center Fuselage - Rear

Image
The rear part of the center fuselage is now largely complete: Some holes are missing however, will have to drill those out:

Fixing fuselage skins defect

Image
After talking with the factory, I had a try at buffing out the damage. Luckily, I had the tools: some brown scotch-brite, and some 3M cut & polish wheels, one light and one medium (also used for deburring edges): I'm not going to detail every single spot that had issues (in the end I found 7 skins with scratches/dents), but it turns out this is real easy to do! Before: After: In one spot, I had chose to use some aluminum epoxy filler: Luckily most of the damage is on the inside of fuselage skins, or on inside skins, so no matter what, the work will never be seen. I still wanted to smooth everything out to make sure that there's no chance of any scratch/dent becoming a crack. Unfortunately there is one noticeable 1.5-1.75cm dent that WILL BE visible from the outside, on the fuselage, forward of the wing leading edge, pilot side: I'm going to have to ask for a new one of those ...

Fuselage kit issues

Image
So inventory is nearly done, and here are my findings so far ... First, no longerons! Apparently the kit is made up of TWO crates (Or more precisely one create and one tube) and Jean forgot to send me the tube!! Doh! How does that happen? Secondly, there's some damage from improper packing it seems: I'll have to check with TAF, especially those two bottom ones, they're on a main piece of skin, and since skin is structural ... I'll have an up close look soon ...

Fuselage kit has arrived!

Image
The fuselage arrived on Friday! Very happy about this major step forward! I am electing to do this first instead of the wings (traditionally one does the wings first) because there's the possibility of new wings being available down the line, and also new wing tips that will fix my lighting issues easily. With the cover off: And with the top layer off: Lots of parts in there, and a very heavy box! Inventory will take some time.